Breguet built XIV A2 of French escadrille Br.11, November 1917 The Breguet XIV This aircraft was the outstanding French day bomber/reconnaissance aircraft of World War I. The Breguet XIV A2 reconnaissance version and the Breguet XIV B2 bomber equipped at least 71 French escadrilles on the Western Front by November 1918 and were also used by units in Serbia, Greece, Macedonia and Morocco. The prototype flew for the first time on 21 November 1916. Following successful deployment by the French, the type was also ordered by the Belgian Army (40 aircraft) and the United States Army Air Service (over 600 aircraft). Around half the Belgian and US aircraft were fitted with Fiat A.12 engines due to shortages of the original Renault 12F. By the end of World War I, some 5,500 Breguet 14s had been produced. and some 8,000 of the type were built up to 1926. Production was spread over eight manufacturers; Breguet, Michelin, Renault, Farmen, Darracq, Bellanger, Schmitt, and SIDAM. The model, textures. panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein, and Microsoft

Michelin built Breguet XIV B2 of USAS 96th Aero Squadron The Breguet XIV This aircraft was the outstanding French day bomber/reconnaissance aircraft of World War I. The Breguet XIV A2 reconnaissance version and the Breguet XIV B2 bomber equipped at least 71 French escadrilles on the Western Front by November 1918 and were also used by units in Serbia, Greece, Macedonia and Morocco. The prototype flew for the first time on 21 November 1916. Following successful deployment by the French, the type was also ordered by the Belgian Army (40 aircraft) and the United States Army Air Service (over 600 aircraft). Around half the Belgian and US aircraft were fitted with Fiat A.12 engines due to shortages of the original Renault 12F. By the end of World War I, some 5,500 Breguet 14s had been produced. and some 8,000 of the type were built up to 1926. Production was spread over eight manufacturers; Breguet, Michelin, Renault, Farmen, Darracq, Bellanger, Schmitt, and SIDAM. The A2 reconnaissance version was followed into production by the B2 bomber version in the summer of 1917, the latter differing in having Breguet-designed automatic full span flaps on the lower wings, lower wing mounted bomb racks, and transparent panels in the sides of the observer's cockpit. The model, textures, bomb, panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein, and Microsoft

This is a set of ten WWII American airfield ground vehicles. These are not really intended as targets although they do have damage files. Rather they are intended to be viewed around the airfield from the player's aircraft. So, they are a bit more detailed than the usual vehicle bgls. Therefore they have a bit larger file, but still not bad. I've put quite a few in a mission without affecting the frame rates. Vehicles: CCKW_353_cover CCKW_353_fuel CCKW_353_open Chevy_110_fire_truck WC_54_ambulance WC_40_light_truck WC_51_ammo _carrier Chevy_M6_bomb_handler Chevy_M6_towing M5_bomb_trailer Credits: Models and textures by Captain Kurt Allen for his "FSDS make exploding object tools" without which I never would have figured out how to create these objects. Nibbio for his vehicle dust effects

Roland Garros’ Morane Saulnier Type L Although not well known, the two seat Morane Saulnier Type L parasol played a large role in WWI aviation between 1914 and 1916. Some 600 were produced by France and used it extensively in the unglamorous reconnaissance role. But it was also the first operational tractor airplane to be armed with a fixed machine gun firing through the propeller arc. The design dated from August 1913 and first 50 Type L parasols were ordered by Turkey rather than by the France. The Aviation Militaire permitted this but required these were to be powered only by a Gnome 50hp engine as all 80hp engines were reserved for French aircraft. They had prototype’s wing span of 33ft, 5 1/2in. When full production was begun, the Type L had a wingspan of 36ft, 9in, wing cutouts to accommodate the observer in the rear seat, a lengthened nose section and other differences. With war imminent and mobilization ordered, the Turkish Moranes were impressed, apparently re-engined with the 80 hp LeRohone 9c, and used to equip two reconnaissance Escadrilles, MS23 and MS26. One of the MS26 pilots was Roland Garros, who was a prewar celebrity air race pilot. The story goes that Garros secured a machine gun and enlisted designer Raymond Saulnier and his personal mechanic Jules Hue to figure a way to enable it to fire forward through the Type L’s propeller arc. Saulnier had been experimenting with a synchronizing interrupter gear, but it was proving erratic. So between Saulnier and Hue they designed a bullet deflector wedge fitted to the propeller which would prevent a bullet from piercing the prop. From photographs it is apparent that Garros was able to equip one of the MS26 impressed Turkish Type L aircraft with the deflector propeller and a Hotchkiss machine gun. This he used to shoot down his first German aircraft on April 1, 1915. He shot down two more on April 15 and April 18. But on April 18 he was also brought down behind German lines by engine trouble. He was able to land uninjured but was captured and the secret of being able to fire directly through the propeller arc was in German hands. The model, textures. panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein. Sounds are from the Nieuport 17 by Gary Aumaugher

The Morane Saulnier Type L Although not well known, the two seat Morane Saulnier Type L parasol played a large role in WWI aviation between 1914 and 1916. Some 600 were produced by France for the unglamorous reconnaissance role. But it was also the first operational tractor airplane to be armed with a fixed machine gun firing through the propeller arc and the first aircraft used to destroy a German Zeppelin in flight. The design dated from August 1913 and first 50 Type L parasols were ordered by Turkey rather than by the France. The Aviation Militaire permitted this but required these were to be powered only by a Gnome 50hp engine as all 80hp engines were reserved for French aircraft. They had the prototype’s wing span of 33ft, 5 1/2in. With war imminent and mobilization ordered, the Turkish Moranes were impressed, apparently re- engined with the 80 hp LeRhone 9c, and used to equip two reconnaissance Escadrilles, MS23 and MS26. At the same time, full production was begun for the Aviation Militaire. With full production, the Type L had an increased wingspan of 36ft, 9in, and wing cutouts to accommodate the observer in the rear seat. Soon design improvements included a lengthened nose section and repositioned landing gear legs among other minor variations. The Aviation Militaire used the Type L extensively throughout 1914, 1915 and early 1916. In 1914, the British RFC in France accepted 52 Type L Parasols for No.3 Squadron with a few going to No.1 and No,12 Squadrons. Also an order of 25 was placed by the RNAS for No.3 wing at Mudros, Lemnos, Greece and No.1 Wing at Dunkerque. Flying from Dunkerque, on June 7, 1915, Flt Sub Lieutenant R. A. J. Warneford destroyed Zeppelin LZ37, the first in mid air, by bombing it with six 20Lb Hales bombs. He was awarded the Victoria Cross for his success. Under licenses obtained just prior to hostilities, Pfalz Flugzeugwerks GmbH produced some 60 virtually identical aircraft, powered by Oberursel engines as the Pfalz A.I, A.II and E.III types (carrying a Spandau MG with an interrupter gear). These were flown by the Bavarian flying units up to mid 1916. Also under license, the Russian companies Duks and Lebed manufactured approximately 450 Type L Parasols for the Czar’s Imperial Russian Air Force.

Pfalz D.XII The Pfalz D.XII was a good aircraft, but it was not as maneuverable as the Fokker D.VII. Thanks to its sturdy wing and thin airfoil section, the D.XII maintained the excellent high-speed dive characteristics of the earlier Pfalz D.III. Like most scouts of the era, however, the D.XII had an abrupt stall and a pronounced tendency to spin. Contemporary pilots consistently criticized the D.XII for its long takeoff run and "clumsy" handling qualities in the air, but consistently compared it against the Fokker D.VII. Rate of roll, in particular, appears to have been deficient. Landings were difficult because the D.XII tended to float above the ground, and the landing gear was weak. Ground crews disliked the extensive wire bracing that accompanied the two-bay wing, again comparing it to the Fokker D.VII which didn't have them. However, it was an improvement over the Albatros D.V and Pfalz D.III which still equipped a number of Jastas and did provide good service. When it was equipped with comparable engines, the Pfalz D.XII could out climb, out dive and was faster than the Fokker D.VII. Between 750 and 800 D.XII scouts had been completed by the Armistice. Early production aircraft had a squared off fin and rudder which lacked control authority. This was soon replaced in production with the rounded fin and rudder on this model. The model, textures. panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein with texture change outs by Captain Kurt. Sound is from the SG Fokker DVII

Pfalz D.XII early production The Pfalz D.XII was a good aircraft, but it was not as maneuverable as the Fokker D.VII. Thanks to its sturdy wing and thin airfoil section, the D.XII maintained the excellent high-speed dive characteristics of the earlier Pfalz D.III. Like most scouts of the era, however, the D.XII had an abrupt stall and a pronounced tendency to spin. Contemporary pilots consistently criticized the D.XII for its long takeoff run and "clumsy" handling qualities in the air, but consistently compared it against the Fokker D.VII. Rate of roll, in particular, appears to have been deficient. Landings were difficult because the D.XII tended to float above the ground, and the landing gear was weak. Ground crews disliked the extensive wire bracing that accompanied the two-bay wing, again comparing it to the Fokker D.VII which didn't have them. However, it was an improvement over the Albatros D.V and Pfalz D.III which still equipped a number of Jastas and did provide good service. When it was equipped with comparable engines, the Pfalz D.XII could out climb, out dive and was faster than the Fokker D.VII. Between 750 and 800 D.XII scouts had been completed by the Armistice. Early production aircraft had a squared off fin and rudder which lacked enough control authority. It isn't known how many were delivered to front line Jastas with the early configuration as it was was soon replaced in production with a rounded fin and rudder. The model, textures. panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein with texture change outs by Captain Kurt. Sound is from the SG Fokker DVII

The Albatros C.III The German Albatros C.III was a highly successful all-purpose two-seat biplane of World War I, used in a wide variety of roles including observation, photo-reconnaissance, light bombing and bomber escort. The C.III was a refined version of the successful Albatros C.I type. It was eventually produced by 6 subcontractor manufacturers as well as Albatros. The first 12 aircraft went to the front in December 1915 and it was gradually withdrawn from frontline service in mid-1917. But production continued for training aircraft. Orders for 2271 aircraft in total were placed with the first 796 ordered for combat units. The remaining 1475 were produced as trainers. Some 26 Albatros C.III were delivered to Bulgaria, including eight trainers and the Polish Air Force operated 15 Albatros C.III in 1918-1920 during Polish-Soviet War. General characteristics • Crew: 2 • Length: 26 ft 1 in (7.95 m) • Wingspan: 38 ft 4 in (11.7 m) • Height: 10 ft 1 in (3.07 m) • Empty weight: 1700 lbs • Gross weight: 2799 lb • Powerplant: 1 × Mercedes D.III 6-cylinder water-cooled in-line piston engine, 160hp (175 hp @ 1400 rpm) Performance • Maximum speed: 156 km/h (97 mph, 85 kn) • Endurance: 3 hours 20 minutes • Service ceiling: 3,350 m (10,990 ft) [16] • Time to altitude: 3,000 m (9,800 ft) in 35 minutes Armament • Guns: 1 × 7.92 mm Parabellum MG14 machine gun in observer's cockpit and 1 × fixed forward-firing 7.92 mm LMG 08/15 in the nose. • Bombs: up to 200 lb (91 kg) of bombs in four vertical tubes in the fuselage or external racks. - The model, textures, panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein with texture change outs by Captain Kurt

The Albatros D.Va The Albatros D.V was developed from the previous D.III design intended to be a lighter fighter with increased performance. However, as soon as it was deployed to frontline Jastas in May 1917, the new type began having catastrophic wing failures. The D.Va was a further development attempting to solve the wing failures. Although externally it appeared similar to the earlier D.V, the Albatros D.Va airframe was beefed up with additional fuselage frames, stronger wing spars and heavier wing ribs. Aileron control cables were moved from the upper wing to the lower wing, an additional wing tip flying wire was added and a supplement “knee” strut was added to the front of the main V wing struts. These last three are the main visual identifiers for the D.Va versus the D.V. Because of the strengthened airframe, the empty weight increased. Speed and maneuverability were degraded but it was still a capable performing fighter. The beefed up construction coupled with some follow on in-the-field modifications finally resolved the wing failures. Large D.Va orders were placed – some 1600 between August and October 1917. It began reaching front line units in October 1917, replacing the earlier D.V’s. The number of Albatros D.Va’s at the front peaked in April 1918 at 928 – 47% of the total German fighter strength. The model, textures. panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein with texture change outs by Captain Kurt, .

Description: he Siemens-Schuckert Werks (SSW) D.III was designed as a fast-climbing interceptor and was to make use of the new 11 cylinder Siemens-Halske 160hp counter-rotary engine. This engine featured a propeller, crankcase and cylinders rotating opposite to the crankshaft, allowing a slower propeller speed for the same power and the elimination of torque, among other things. Initial tests of the Sh.III engine in the SSW D.IIb saw a remarkable (for the time) climb of 7000m in 35 minutes, and the decision was made to design a new interceptor around it. Approximately 41 SSW D.IIIs were delivered to frontline units between April and May, 1918. Most aircraft were supplied to Jagdgeschwader II, whose pilots were enthusiastic about the new aircraft's handling and rate of climb. however after 7 to 10 hours the Siemens-Halske engines began having problems with overheating and piston seizures. The airplanes were returned to the factory for upgrading. They were retrofitted with modified engines, cutaway cowlings, shorter wings, new design ailerons and rudder. They were returned to service in late July 1918 along with a further 30 newly manufactured D.IIIs incorporating the design changes. They were issued to home defense Kest Squadrons this time, because their fast climb capability made them ideal to intercept incoming Allied high altitude bombing raids. The model, textures. panel and air files are by Captain Kurt. The pilot figures were developed from Wolfi's freeware Japanese pilot .fsc source file. The prop spinning texture is by Kelticheart. Gauges are by Martin Klein with texture change outs by Captain Kurt