CFS2 Hiryu B5N2 KATE Textures only for The B24 Guy's Overhaul B5N2 Model."B5N2" Texture and Damage Files Only.Author: Evan G. Butterbrodt. 1.9MB

Messerschmitt Bf 109E-3 by Design Team Daedalus Unit: 1./JG 26 1940 Caffiers, France Pilot: Oblt. Walter Blume To improve the performance of the Bf 109E, the last two real prototypes (V16 and V17) were constructed. These received some structural improvements and more powerful armament. Both were the basis of the Bf 109 E-3 version. The E-3 was armed with the two MG 17s above the engine and one MG FF cannon in each wing. Some units began recieving the E-3 by September 1939. A total of 1,276 E-3 were built, including 83 E-3a export versions. There were many small differences between indivual E-3s because the E-3 was often modified in the field by groundcrew and rear area repair depots. The production standard had no pilot armor. Mods included types of pilot head armor,E-4 type squared canopies, E-7 type pointed spinners, etc. So each model we have created has its own unique features. This aircraft was modified with flat plate pilot head armor. Pstrany is the primary model author with some small model refinement and additions by Captain Kurt as the model was collaborated on during development. Captain Kurt created the textures for each, the 2D instrument panel, the individual .dp files, air files and aircraft.cfg files.

Messerschmitt Bf 109T-2 by Design Team Daedalus Unit: 2./JG77 Lister, Norway 1941 Pilot: unknown The Bf 109T was based on the E-7 and designed as an aircraft carrier fighter intended to serve on Germany's then under construction carrier, the Graf Zeppelin. The wing span was increased to 36 feet, 4.22 inches, a small spoiler was added to the top of the wings, and added an arrestor hook and catapult fittings. An order for 70 was placed with Fieseler with construction fully underway in April 1941. When construction of the Graf Zeppelin was cancelled, the remaining 63 of 70 T-1s were built as T-2s with the carrier equipment either removed, or inactivated like the wing top spoilers. Some of the T-1s may have been converted to T-2 standard. It was found that the flight performance of the T-2 was closely comparable to the E-4/N. Because of its ability to take off and land in shorter distances, 42 T-2s were assigned to I/JG.77 and 21 T-2s were assigned to Jagdgruppe Drondheim in June 1941, both units being deployed in Norway on landing strips which were both short and subject to frequent, powerful cross-winds. In April and May 1943 a few remaining T-2s were operational with 12 assigned to Jagdstaffel Helgoland (subordinated to JG 11) and 10 were with JG300 as night fighters. a few others were scattered around with training units. With a production run of only 70 units the planes were fairly standardized, but field modifications did exist on some planes. So each model we have created has its own unique features. This aircraft was equipped with a flat plate plus curved top pilot head armor. Pstrany is the primary model author with small model refinements and additions by Captain Kurt as the model was collaborated on during development. Captain Kurt created the textures for each, the 2D instrument panel, the individual .dp files, air files and aircraft.cfg files.

Messerschmitt Bf109F-4Trop by Design Team Daedalus Unit: 5./JG27 Egypt, 1942 Pilot: Hptm Ernst Boerngen There is no "standard" Bf 109F-4, as the production run underwent many small modifications and there were field implemented updates along the way. So each model we have created has it's own unique features. Pstrany developed the models using Paul Rebuffat's Messerschmitt model - with permission - as a starting framework and updated the shape, and added a plethora of details, new parts, and ideas. Pstrany also developed the models for the drop tanks, weapons and racks. Captain Kurt created paints for each, the 2D instrument panel, the individual .dp files, the air files and the aircraft.cfg files. Mav SCASM edited each model so that they have animated wing slats, drop tanks, and other features, as well as optimizing models for the best possible framerates. Mav also developed the idea for the 2d panel to be offset for the Revi gunsight to match the CFS2 reticle.

Messerschmitt Bf109F-4/R1 by Design Team Daedalus Unit: 2./JG52 east front, 1942 Pilot: unknown There is no "standard" Bf 109F-4, as the production run underwent many small modifications and there were field implemented updates along the way. So each model we have created has it's own unique features. A number of F-4's had 2 field installed R1 rustzaste 20mm under-wing gondolas to increase the firepower. Pstrany developed the models using Paul Rebuffat's Messerschmitt model - with permission - as a starting framework and updated the shape, and added a plethora of details, new parts, and ideas. Pstrany also developed the models for the drop tanks, weapons and racks. Captain Kurt created paints for each, the 2D instrument panel, the individual .dp files, the air files and the aircraft.cfg files. Mav SCASM edited each model so that they have animated wing slats, drop tanks, and other features, as well as optimizing models for the best possible framerates. Mav also developed the idea for the 2d panel to be offset for the Revi gunsight to match the CFS2 reticle.

Messerschmitt Bf109G-4 by Design Team Daedalus Unit: Pilot: The Bf 109G-4 was an incremental development of the G-2. The 1475hp DB605A engine and armament was unchanged from the G-2. The tire size increased from the previous 650 x 150 size to 660 x 160 to better handle the increasing weight of the G series. It still used the spoked wheel rims carried over from the G-2 series but the increased tire size required kidney shaped bulges to be added to the top of the wings above the wheel wells. A larger 350 x 135 tail wheel replaced the earlier 290 x 110 size. Because the larger tail wheel would not fit in the tail wheel recess, the retraction mechanism was disconnected and the tail wheel was fixed in the down position. The radio was replaced with the more powerful FuG 16Z. With a growing tactical need for timely reconnaissance, 80 of the G-4 production was dedicated to mount a 12.5cm Schneider-Gottingen camera in the belly and controls in the cockpit. Some, intended for longer range missions, also received redesigned wings incorporating a rack to carry a drop tank. It was produced from September 1942 to May 1942: G-4 production = 727 G-4/trop production = 435 G-4/R3 (reconnaissance) = 80 Still, there was no standard G-4. Three separate companies and multiple sub-assembly production facilities were involved which inevitably produced minor variations, such as pilot head armor type, cockpit vents, tail wheel types and field added Rustsatze kits. So, each model we have created has its own unique features to portray the specific aircraft as accurately as possible. This aircraft was a short range R3 photo reconnaissance version mounting a single centerline drop tank. It had an Rb75x30 camera in the belly just behind the wing. The cowl mounted MG17 machine guns were removed and the openings faired over to save weight, the main landing gear tires used the later G-6 type flat face hubs, the fixed tail wheel gear had a dust cover boot and the tail wheel bay was faired over. It used a broad blade prop, had a deeper oil cooler and rear small cowl scoops were cut back. It had a 2 piece curved top pilot head armor, a cockpit vent scoop on the starboard side, and a rear view mirror was fitted to top of the canopy. Pstrany developed the models using Paul Rebuffat's Messerschmitt model - with permission - as a starting framework and updated the shape, and added a plethora of details, new parts, and ideas. Pstrany also developed the models for the drop tanks, weapons and racks. Captain Kurt created paints for each, the 2D instrument panel, the individual .dp files, the air files and the aircraft.cfg files. Mav SCASM edited each model so that they have animated wing slats, drop tanks, and other features, as well as optimizing models for the best possible frame rates. Mav also developed the idea for the 2d panel to be offset for the Revi gun sight to match the CFS2 reticle.

Messerschmitt Bf109G-2 R6 by Design Team Daedalus Unit: 6./JG52 Maykop, Russia, October 1942 Pilot: Lt. Walter Krupinski During the summer of 1941, the Messerschmitt design team was engaged in updating the BF 109F-4 as the dictates of the air war was forcing the need for greater speeds. The result was the Gustav series, of which the first substantial production run was the Bf 109G-2. Adopting the more powerful but heavier Mercedes Benz DB 605 engine required airframe and landing gear strengthening which also added weight. But it was felt the increase in speed made the loss of some maneuverability acceptable. The fuel filler access was moved to the spine behind the cockpit. No change was required for the cowling shape but a deeper oil cooler was needed. The broad blade of the F4/Z was made standard. The lower quarter cockpit window panel was deleted and vent scoops could be added to the new replacement metal panel. The wheel wells reverted to a squared end in anticipation of wheel covers that in the event were not adopted. Generally speaking the appearance of the G-2 was very similar to the F-4 without close examination. Deliveries of the G-2 began in May 1942 with 1,587 produced by February 1943. However, there is no "standard" Bf 109G-2. Although production only ran 10 months before the G-3 and G-4 were introduced, three separate companies and multiple sub-assembly production facilities were involved which inevitably produced minor variations, such as pilot head armor type, cockpit vents and tail wheel types. So each model we have created has its own unique features to portray the specific aircraft presented as accurately as possible. This aircraft had no cockpit vents, a flat plate pilot head armor, a retractable tail wheel and was fitted with MG 151/15 under wing cannon gondolas. Pstrany developed the models using Paul Rebuffat's Messerschmitt model - with permission - as a starting framework and updated the shape, and added a plethora of details, new parts, and ideas. Pstrany also developed the models for the drop tanks, weapons and racks. Captain Kurt created paints for each, the 2D instrument panel, the individual .dp files, the air files and the aircraft.cfg files. Mav SCASM edited each model so that they have animated wing slats, drop tanks, and other features, as well as optimizing models for the best possible framerates. Mav also developed the idea for the 2d panel to be offset for the Revi gunsight to match the CFS2 reticle.

Messerschmitt Bf109G-2 by Design Team Daedalus Unit: 9./JG54 Siverskaya, Russia, September 1942 Pilot: Obfw. Wilhelm Schilling During the summer of 1941, the Messerschmitt design team was engaged in updating the BF 109F-4 as the dictates of the air war was forcing the need for greater speeds. The result was the Gustav series, of which the first substantial production run was the Bf 109G-2. Adopting the more powerful but heavier Mercedes Benz DB 605 engine required airframe and landing gear strengthening which also added weight. But it was felt the increase in speed made the loss of some maneuverability acceptable. The fuel filler access was moved to the spine behind the cockpit. No change was required for the cowling shape but a deeper oil cooler was needed. The broad blade of the F4/Z was made standard. The lower quarter cockpit window panel was deleted and vent scoops could be added to the new replacement metal panel. The wheel wells reverted to a squared end in anticipation of wheel covers that in the event were not adopted. Generally speaking the appearance of the G-2 was very similar to the F-4 without close examination. Deliveries of the G-2 began in May 1942 with 1,587 produced by February 1943. However, there is no "standard" Bf 109G-2. Although production only ran 10 months before the G-3 and G-4 were introduced, three separate companies and multiple sub-assembly production facilities were involved which inevitably produced minor variations, such as pilot head armor type, cockpit vents and tail wheel types. So each model we have created has its own unique features to portray the specific aircraft presented as accurately as possible. This aircraft had no cockpit vents, a 2 piece curved top pilot head armor, and a retractable tail wheel. Pstrany developed the models using Paul Rebuffat's Messerschmitt model - with permission - as a starting framework and updated the shape, and added a plethora of details, new parts, and ideas. Pstrany also developed the models for the drop tanks, weapons and racks. Captain Kurt created paints for each, the 2D instrument panel, the individual .dp files, the air files and the aircraft.cfg files. Mav SCASM edited each model so that they have animated wing slats, drop tanks, and other features, as well as optimizing models for the best possible framerates. Mav also developed the idea for the 2d panel to be offset for the Revi gunsight to match the CFS2 reticle.

Messerschmitt Bf109G-2 by Design Team Daedalus Unit: 7./JG54 Isotscha Airfield, Smolensk, Russia, Winter 1942-43 Pilot: unknown During the summer of 1941, the Messerschmitt design team was engaged in updating the BF 109F-4 as the dictates of the air war was forcing the need for greater speeds. The result was the Gustav series, of which the first substantial production run was the Bf 109G-2. Adopting the more powerful but heavier Mercedes Benz DB 605 engine required airframe and landing gear strengthening which also added weight. But it was felt the increase in speed made the loss of some maneuverability acceptable. The fuel filler access was moved to the spine behind the cockpit. No change was required for the cowling shape but a deeper oil cooler was needed. The broad blade of the F4/Z was made standard. The lower quarter cockpit window panel was deleted and vent scoops could be added to the new replacement metal panel. The wheel wells reverted to a squared end in anticipation of wheel covers that in the event were not adopted. Generally speaking the appearance of the G-2 was very similar to the F-4 without close examination. Deliveries of the G-2 began in May 1942 with 1,587 produced by February 1943. However, there is no "standard" Bf 109G-2. Although production only ran 10 months before the G-3 and G-4 were introduced, three separate companies and multiple sub-assembly production facilities were involved which inevitably produced minor variations, such as pilot head armor type, cockpit vents and tail wheel types. So each model we have created has its own unique features to portray the specific aircraft presented as accurately as possible. This aircraft had its landing gear doors removed to prevent snow build up, cockpit vents on both cockpit sides, a 2 piece curved top pilot armor and a non-retractable tail wheel. Pstrany developed the models using Paul Rebuffat's Messerschmitt model - with permission - as a starting framework and updated the shape, and added a plethora of details, new parts, and ideas. Pstrany also developed the models for the drop tanks, weapons and racks. Captain Kurt created paints for each, the 2D instrument panel, the individual .dp files, the air files and the aircraft.cfg files. Mav SCASM edited each model so that they have animated wing slats, drop tanks, and other features, as well as optimizing models for the best possible framerates. Mav also developed the idea for the 2d panel to be offset for the Revi gunsight to match the CFS2 reticle.

Messerschmitt Bf109G-6 trop by Design Team Daedalus Unit: 6./JG51 Either San Pietro, Italy, or on Sardinia during the summer of 1943 Pilot: unknown There is no "standard" Bf 109G-6, as the production run spanned 2 years it underwent many modifications and updates along the way. Tropical versions were delivered throughout the entire production runs as the G-6 trop but had fewer variations. For example I have not seen any G-6 trop aircraft fitted with an Erla Haube canopy while many G-6 versions were so fitted. The most obvious feature of the G-6 trop was the sand filter fitted to the front of the supercharger air intake. All G-6 trop aircraft had two small teardrop shaped clips on the port side below the canopy sill, which were mounts for a sun umbrella. The umbrella was intended to provide shade for the cockpit while the aircraft was at readiness. Different weapons packages could be seen. Most Most G-6 trops were delivered to the Mediterranean operations areas and some to the southern Russian/Balkans front area. Pstrany developed the models using Paul Rebuffat's Messerschmitt model - with permission - as a starting framework and updated the shape, and added a plethora of details, new parts, and ideas. Pstrany also developed the models for the drop tanks, weapons and racks. Captain Kurt created paints for each, the 2D instrument panel, the individual .dp files, the air files and the aircraft.cfg files. Mav SCASM edited each model so that they have animated wing slats, drop tanks, and other features, as well as optimizing models for the best possible framerates. Mav also developed the idea for the 2d panel to be offset for the Revi gunsight to match the CFS2 reticle.