Cr-1 RATA Package. This is add-on started out as simTECH Flight Design project of interest back in 2002. Then it went on the shelf until Feb 2009. I since sold SimTECH Flight Design Ltd but retained rights to all older simTECH models as well as models under development. Hence this great little model…Months later here we are with a full release Rata. The model is a Rhino 3d model which I later exported the model into a custom made compiler so it could be accepted in Fs9. This is a very old model so some of the newer features That the newer FS9 and FSX flight Sims support are not in this add-on. It took a lot of reverse programming to get this model to the point that is now. This model is set up specifically for Fs9 and will not work well in fs2002 or FSX. It will work in FSX AND Fs2002 but some additional modifications will have to be made, but it is possible to do so And I give any crafty designer the permission to do so as long as the Cr-1-Software LTD. trade mark and copy write is left intact. Tom Woods/ SimTech

Bo-105 IFA German Rescue. Original is model by Güther Krämer

The Zlin Z-43 is a Czech four seat light trainer and touring aircraft. A development of the two seat Zlin Z-42. It is a low winged monoplane. The Zlin Z-43 first flew on December 1968. This is a fictitious paint scheme based on some hand drawings published in my book "Faszination Borkum". My Tribute to the biggest of the Ost Frisian islands. Textures only, requires pwzlin43.zip.

USA South East USGS 10 metre mesh terrain - FSX only. This constitutes 10 metre terrain mesh for a section of the USA, The whole USA East mesh files will abutt the US West Coast 10m mesh already available, that was made by: Raimondo Taburet. Make sure you have your scenery terrain settings at about 5 metres in the FSX display dialogue for the mesh to show properly! Includes: NM, TX, LA, MS, AL, FL, GA, SC.

Flying in this region is considered by IATA as a "Black Cross Region" so they take no members from this area .No world ensurance company works around here so planes and pilots are hard to get. There is a Shuttle service called in Indu " Wings of the Lucky Elephant" or Bugli Air Service. It takes off early in the morning with almost anything like people, chickens, rope, paint gallons, nails and sometimes caged cobras sent out to some witch doctor from the local snake market. This "airline" is not new. Back in 1947 Duart Mooresby started the business with an old 1939 DC-3 and his son continued it in the sixties with another used C-46 and a twin Anson. Now Duarts's grandson is flying the route with a Caribou and the same fixed up DC-3 his grandfather almost got killed in many a time. Flying here is a question on having good eyes and a good butt since flying by the seat of your pants is paramount. There are no radio aids only the two way radio from their shack at the airport. Mountains are all over and the airfields served are located in very pretty but awfully dangerous tiny valleys wedged inside the towering rocks of the said mountains. So why fly here?..The local birds think its nice and there are a lot of worms around the fields. Bugli Air Service has bought a New Twin Otter and you will be delivering it, teaching the two pilots how to fly it in the mountains and finally, if you don't end up in the local Red Cross aid station, get a "Real Bush Pilot" certificate which only Bugly Air provides in this planet. It is said, down in South Africa, that if you get this certificate you can fly like an eagle anywhere in the whole wide planet. Good luck Piloto

USA South East USGS 10 metre mesh terrain - FSX only. This constitutes 10 metre terrain mesh for a section of the USA, The whole USA East mesh files will abutt the US West Coast 10m mesh already available, that was made by: Raimondo Taburet. Make sure you have your scenery terrain settings at about 5 metres in the FSX display dialogue for the mesh to show properly! Includes: NM, TX, LA, MS, AL, FL, GA, SC.

USA South East USGS 10 metre mesh terrain - FSX only. This constitutes 10 metre terrain mesh for a section of the USA, The whole USA East mesh files will abutt the US West Coast 10m mesh already available, that was made by: Raimondo Taburet. Make sure you have your scenery terrain settings at about 5 metres in the FSX display dialogue for the mesh to show properly! Includes: NM, TX, LA, MS, AL, FL, GA, SC. This BGL file has a half degree block missing due to bad data occuring in the USGS GeoTIFF file I downloaded. Tried fixing it...but to no avail. The missing block covers a rectangle with its bottom left corner at: Lat: 30.0000, Long: -83.5000, and its top right hand corner at: Lat: 31.0000, Long: -83.0000. See jpg image in folder.

USA South East USGS 10 metre mesh terrain - FSX only. This constitutes 10 metre terrain mesh for a section of the USA, The whole USA East mesh files will abutt the US West Coast 10m mesh already available, that was made by: Raimondo Taburet. Make sure you have your scenery terrain settings at about 5 metres in the FSX display dialogue for the mesh to show properly! Includes: NM, TX, LA, MS, AL, FL, GA, SC.

USA South East USGS 10 metre mesh terrain - FSX only. This constitutes 10 metre terrain mesh for a section of the USA, The whole USA East mesh files will abutt the US West Coast 10m mesh already available, that was made by: Raimondo Taburet. Make sure you have your scenery terrain settings at about 5 metres in the FSX display dialogue for the mesh to show properly! Includes: NM, TX, LA, MS, AL, FL, GA, SC.

USA South East USGS 10 metre mesh terrain - FSX only. This constitutes 10 metre terrain mesh for a section of the USA, The whole USA East mesh files will abutt the US West Coast 10m mesh already available, that was made by: Raimondo Taburet. Make sure you have your scenery terrain settings at about 5 metres in the FSX display dialogue for the mesh to show properly! Includes: NM, TX, LA, MS, AL, FL, GA, SC.